These were all ran right around 2600fps. Banged steel 6″ gong @200yds
I ended up holding -13MOA on the scope and holding the left edge to ring hits. Most fun was doing double and triple taps on the plate.
Brass Used was a mix of New, 1x and 2x fired Starline match prepped: converted 6.5 Grendel, annealed, neck turned, inner neck champhered and honed. Brass looked good, Flat primers, slight ejector mark. Max charge decided on previously, this was just to test functionality. Wolf SRM Primers and LeverEvolution.
I did have a few Failure to feeds on the 108 EHs Loading them in the mag they are very long and may need to seat them a bit deeper. It seems like the tips are hitting the top of the chamber and getting stuck and the bolt just rides over the lip to jam in the shoulder.
Its been fun riding the hell out of this Poverty Pony to the land beyond 750yds. Now I have dope, ammo, equipment, and experience to shoot the AR-15 platform from 100-1000 yards with no scope dialing.
Started off with zeroing the rifle at 100 with the yellow box of BTTs @2500. These were plinker rounds and nothing special. At 100/200/300 hits were no problem tried a couple shots at 500 but wasn’t 100% on that and it was near the buzzer so not bad for first round.
Shout out to WLS – the We Like Shooting Podcast/Youtube channel. The guys there know their stuff and keep you up on new products in a funny and charismatic way. Check out the latest episodes on You Tube.
Next buzzer round(about 30 mins) I just single fed rounds to Fire Form – shooting them at 2/3/500 pretty easily – These are slow rounds @2400. Taking slow shots on bags with the new glass is where I really settled in. The glass was crisp and the side focus was nice, the dials are nice, the mount seems solid, all in all the glass choice is greenlighted – All the money spent where you want it.
Then started dialing in elevation to get and test the 100-1000 hold theory. So The theory is just dial for 600 yd zero and then use hold under/overs so that there is no dialing. At 100 sighting plate, dialed -6MOA and test fired = 6” higher. This confirmed my dialing so I dialed in a total of -19MOA and took another test shot confirming the elevation on the 100 yd plate.
Then went back with the Slow and Low ammo @2500, and confirmed dope on the short range 1/2/3/500. I was able to hit some of the smaller swingers at 500 even the next to smallest swinger a couple times. One thing I DID notice is that when using the Hold Unders is that the windage is not marked on the upper part of the reticle like it is on the lower part of the reticle. when I was having to hold -2MOA wind and 2MOA elevation, it was a tad trying. Still I think that is a bit of nitpicking overall the new glass made hits easy. I finished the buzzer round and prepped for moving to the long range.
There was a little dialing in zero for 600 and the wind, but once that is settled, the holds worked GREAT! NO DIALING! I was able to make hits at 600 and 750.
I tried for 1k with the slow and low ammo a couple times, at 27MOA I was aiming a bit low I believe but I wasn’t getting confirmed hit so I stopped. I was holding above the “O” in MOA in the reticle. In retrospect, I believe I could make hits holding 25MOA – It appears that Strelock Pro may have lowered the velocity due to temp algorithm a bit and cause more MOA than needed.
There were some other people shooting the plates and the monitors were off, making confirmation of hits a bit more challenging. Again, the glass here made it able to spot shots easier than before. I didn’t even bring my spotting scope.
With the afternoon range day-light starting to run out, I figured this was my shot to try for 1k so broke out the good Fast ammo and and confirmed 600 yd zero. 750 seemed to be a tad less hold than I had estimated and I then tried 1k on the plate and got a hit, thus confirming holds. Next round of the buzzer with a clean paint on 1k I was able to sprinkle ~ 10 out of 15 shots on the large circle plate and even a few shots on the smaller plate as well. I just finished shooting all the ammo I had.
At the end of the day I Annealed 427 brass ready for the good stuff! Goodbye 223! Made some new Laminated Load cards.
So, I got bored and made a new video about new(to me) old CZ97B Safety model.I got some video editing practice. Digg the 97s (CZ FuddRunner) – it was a great day! The trigger action and shape of the older one has the slight nod, but the newer model has better sights and LOK grips(upgrade). […]
We all have things to work on… I try to be the person to at least think those words when disposition comes along. I’m starting to feel really great about breaking bad habits. In particular for today is You Tube… So I started up Rumble and what do you know one of the first things […]
Disclaimer: do your own research and use common sense when reloading. I am not responsible for your results. Don’t try this at home or at home office either… Here are the steps that worked for me. I wouldn’t even attempt this without a great annealer. That thing is worth its weight in brass. Scope footage: […]
Executive Summary – it was windy, I learned a LOT about wind today. So windy in fact many of the more experienced shooters had issues with the wind. There was “supposed” to be an option for 1250 yds, but that was nixed due to wind. I have shot this gun 6ARC and ammo at 1k […]
Ive been looing forward to this test for a while and finally made it to the range to make it happen. The goal was to test High Velocity match ammo @200 and see if I could have a 50yd(or 100yd) zero and use BDC reticle out to 200yds. The Rig: Ruger Mk 4 lower gutted […]
Took the new Mile Rifle to Skyline to group in @ 200yds and run the 2n’d round of ladder loads. All rounds with H225 ELDM over 7828SSC or N565. I shot all but the hottest rounds for each powder, making a specific point to leave the hot rounds for next time – enforce the It’s […]